Forum: CoCreate Modeling Personal Edition
11-30-2009, 01:18 PM
|
Replies: 2
Views: 3,947
Re: Intersecting Profiles
I need a mitre. It's not as easy as doing a 45degree workplane and subtracting. Since different parts of each profile intersect at different points. Picture attached.
I've managed to do it, but...
|
Forum: CoCreate Modeling Personal Edition
11-26-2009, 02:55 AM
|
Replies: 3
Views: 7,292
|
Forum: CoCreate Modeling Personal Edition
11-26-2009, 12:11 AM
|
Replies: 11
Views: 13,307
Re: TetraHedron
Thanks for that; excellent tips. I successfully created one perfect tetrahedron using this method. Kind of easier than Inventor even! ;-)
|
Forum: CoCreate Modeling Personal Edition
11-25-2009, 11:45 PM
|
Replies: 2
Views: 3,947
Intersecting Profiles
Hi Guys - New Question.
I have two extruded profiles that intersect. I need a clean diagonal cut from the inside corner to the outside corner so that both profiles meet. It is a door frame and I...
|
Forum: CoCreate Modeling
11-25-2009, 09:38 PM
|
Replies: 7
Views: 5,482
Re: model screw
Perfect. Thanks Mike. Very nice of you to go to the effort of doing it and pasting it here.
Regards,
K.
|
Forum: CoCreate Modeling
11-25-2009, 01:16 PM
|
Replies: 7
Views: 5,482
|
Forum: CoCreate Modeling
11-24-2009, 09:29 PM
|
Replies: 7
Views: 5,482
Re: model screw
Can someone show me step-by-step how to get that screw thread??? I tried doing this but im not sure about the profiles.
|
Forum: CoCreate Modeling Personal Edition
11-24-2009, 11:43 AM
|
Replies: 11
Views: 13,307
Re: TetraHedron
Admittedly i missed the first method ;-)
To answer your question about how i did it in inventor. Create the triangle, create a workplane extending up into 3d space, create a single line from the...
|
Forum: CoCreate Modeling Personal Edition
11-24-2009, 11:32 AM
|
Replies: 2
Views: 4,636
Re: Sweep
Worked perfectly! Thanks. I really appreciate it
|
Forum: CoCreate Modeling Personal Edition
11-23-2009, 04:20 PM
|
Replies: 2
Views: 4,636
Sweep
I'm trying to sweep a profile with a circle to create a cylindrical shape... but i'm stuck. Any ideas on how to achieve this?
It will effectively be a "handle".
|
Forum: CoCreate Modeling Personal Edition
11-23-2009, 02:41 PM
|
Replies: 11
Views: 13,307
Re: TetraHedron
Thanks for that - I managed to create the tetrahedron but measurements were off slightly after it was created. How do you get the centrepoint of the circle to be the same plane as W1? If i start at...
|
Forum: CoCreate Modeling Personal Edition
11-23-2009, 02:06 AM
|
Replies: 11
Views: 13,307
TetraHedron
In Inventor it's easy to create a tetrahedron (Triangular based pyramid). I create a work plane, draw my equalateral triangle, draw an intersecting workplane; draw a line in the centre of the...
|
Forum: CoCreate Modeling Personal Edition
11-23-2009, 02:04 AM
|
Replies: 0
Views: 4,107
No Valid License Error
I installed CoCreate on Windows7. The splash screen comes up and then immediately goes to "No Valid License" error. I have even run this in WinXP compatibility mode.
I disabled all virus/malware...
|