Readme for ACCURACY ADVISOR (Short cut: AA of aa) ************************************************************** INSTALLATION In ME10 go to the directory where the "accuracy advisor" macro is stored and enter: INPUT 'accuracy.mac' The command AA should be used to start the advisor macro. The macro could also be included in the dimension menu. ************************************************************** SYNTAX Please refer to web page: http://www.nethut.net/me10/accad_2/accuracy_advisor_frame.htm for a detailed description. ************************************************************** DESCRIPTION For decades, the "accuracy" of a technical drawing has been judged by the ease of manufacture and assembly of the component. If the final product was satisfactory then the drawing describing the component was "accurate". While ever paper drawings have been the basis for manufacture the actual geometrical accuracy has been of secondary importance. Today 3D models are used directly for production. Data is transferred from the design system to the machining system. In some cases no drawings are generated - accuracy is fine if the final result of production and assembly is good. In this case the dimensions could be "irrational" - for example 24.7513244423mm - the important thing is that the components fit together. If however, 2D drawings are used in the manufacture of components then the dimensions should, ideally, be "rational" for example 24.75mm. This way it will be much easier to manage the design and production processes. Designers will be able to communicate dimensions verbally. Relationships between components (e.g. clearances) can be considered without being concerned about the "unseen" decimals. 2D-drawings sent electronically (2D-dxf,iges) should contain only rational dimensions as CNC systems work slavishly with an accuracy greater than that our drawing standards anticipated. CAD systems allow dimensioning to a specified number of decimal places, 2 are common. If a vector with a length 24.7513244423mm is dimensioned it will show 24.75(mm). The system will probably not inform the user that the geometry is in fact 0.0013244423mm longer! CAD systems help the user to work accurately, but if an error does occur then it will tend to spread into other areas like a virus. Many hours of detective work must be spent if the original error is to be found. If the error is critical and the cause cannot be found then it must be compensated for elsewhere. The Accuracy Advisor can help in finding geometrical and dimensional errors (anomalies). If a dimension is incorrect and the geometry does not correspond exactly the user may adjust the geometry. The Accuracy Advisor allows easy access to geometric data (length, radius etc,) and highlights the grades of elements accuracy found in the drawing. At the time of writing only the decimal format of dimensions is supported. Feet, inch and fractions are not suitable for dimensional analysis. Definition of "accuracy" ME10 does a very good job of managing fundamental geometric accuracy. Under normal conditions it works to 13 decimal places! On the other hand an ME10 user can be very poor in exploiting this! Errors can be made in selecting the points for a rotation; values can be obtained manually with a calculator or the cursor can merely catch the wrong points. It is not uncommon that errors of 0.001mm occur. Accuracy Advisor looks at the length of lines and the radius/ diameter of circles, arcs and fillets. The user can define to which level of accuracy these elements should be compared. The most important feature though is the ability to analyse dimension's displayed value against the geometry it describes. It is this difference which gives the "error". If a dimension shows 32.76 but the geometry measures 32.7610867856 then the error is 0.0010867856mm. Accuracy Advisor deals with three levels of accuracy: GOOD, OK and BAD. ************************************************************** RECOMMENDED SETTINGS/ADVICE ACCURACY ADVISOR has been deveoped to work with mainly decimal format dimensions. Feet, inches and fractions are not supported except when converted to decimals. At present it is advisable to avoid working with green(!) or grey viewports. If you do the adjust arrows will disappear and the tables hard to follow. STORE DRAWING BEFORE EXECUTION - Always wise, especially when working with a drawing containing lots of geometry. ************************************************************** KNOWN BUGS/PROBLEMS Sometimes a geometry may be classed as "OK" when it is actually "GOOD". DISPLAY The latest Windows version of ME10 9.0 has a peculiar "Windows thing" about it - it brings up a window saying "OK"! This is very annoying because when using "Info" the table is very often covered up by the window. Because of this instead of using "DISPLAY" then a "READ PNT" is used hence requiring the input of a point to continue.